Tags
Clogged, Clothes Dryer, Family, Heating, Humor, HVAC/R, laundry, Life, Lint, Machanical, parts, Troubleshooting, Voltmeter, writing
First of all, let me explain something. I’m an HVAC/R technician by trade. I can work on most heating and air-conditioning systems with little to no trouble. I can troubleshoot just about any electronic or mechanical device and usually figure out how to repair it. I have a pretty good amount of confidence in my mechanical and electrical abilities.
However, apparently, there is one appliance in my house that has decided to challenge everything I thought I knew about repairing things: the clothes dryer!
And not just any dryer. This is an older dryer, built before everything had to have a computer, digital display, and enough electronics to launch a space shuttle. You would think this would be one of the easiest appliances to work on.
You would think wrong!
Here’s the story.
A few weeks ago, I noticed that our dryer was making an unusual noise. It sounded like a bad bearing, and having worked on the dryer before, I knew there were two drum rollers that supported the drum. Each had a bearing inside. There was also a tensioning bracket with a roller that the belt rode on.
So, I did what any good do-it-yourself repairman would do. I ordered two new drum rollers and a tensioning bracket. Since I would already have the dryer torn apart, I figured I might as well replace the belt while I was in there.
The parts arrived, but since everything else seemed to be working, I wasn’t in any particular hurry to install them. After all, I had several craft shows to prepare for, and those were taking up most of my time.
Then came the conversation that started this whole adventure.
I’m sitting in my recliner watching television when my wife walks into the room and says, “I know you have parts to repair the dryer, but I thought I’d tell you that the dryer isn’t drying the clothes.”
I asked her how long this had been going on.
Her response? “A few weeks.”
A FEW WEEKS?
Apparently, this little detail had slipped through the communication department!
Anyway, now I had another problem to troubleshoot. The dryer was running, but it wasn’t heating properly. My first thoughts were a bad heating element, thermostat, or thermal cutoff.
I pulled the dryer away from the wall, grabbed my trusty voltmeter, and started checking everything. The heating element checked out. The thermostat checked good. All the safety devices checked out.
The only thing I could think of was the thermostat, so I ordered a replacement.
A few days later, the part arrived. I installed it, confident that I had found the problem.
Nope!
Still not working.
I grabbed my voltmeter again and went through the same testing routine. Everything checked out just like before. At this point, I was beginning to wonder if the dryer was simply messing with me.
Then I noticed something.
The dryer was running, so I opened the door. As expected, the dryer shut off and the drum stopped spinning. However, I could still hear something spinning inside the dryer.
Interesting.
I closed the door, pushed the start button, and let it run again. I opened the door, and the same thing happened. The drum stopped, but something inside continued spinning.
Back to the drawings!
After studying the diagrams again, I found one other component I hadn’t considered: the blower wheel. This little wheel is responsible for circulating the hot air through the drum and pushing the moist air out through the dryer vent.
Could that be the problem?
I placed another order.
At the rate I was going, I figured I would eventually replace every part in the dryer. At least by then I would know what wasn’t wrong with it!
The blower wheel arrived yesterday, and after watching several YouTube videos, the repair looked pretty straightforward. Most of the videos suggested it should take somewhere between 15 and 30 minutes.
Right!
We started around 2:15 in the afternoon and finally finished around 6:15.
Apparently, YouTube forgot to mention a few things.
The blower wheel had actually stripped out on the motor shaft, which made removing it quite a challenge. I eventually had to cut the old wheel off. Unfortunately, the bushing holding it onto the shaft was seized solid. Out came the blowtorch, and after applying some heat to the shaft, I finally managed to get the bushing loose.
You would think that once I got that bushing off, things would get easier.
I thought so, too.
Not so much.
I love my wife dearly, and I appreciate her willingness to help me, but let’s just say mechanical repairs aren’t exactly her area of expertise. She doesn’t necessarily know the difference between a wrench and a screwdriver.
The problem was that I had her positioned on one side of the dryer and me on the other. I was trying to explain what I needed her to do, but she couldn’t see what I was talking about, and I wasn’t in a position to show her.
It made for some interesting communication!
The dryer motor has what we call a dual shaft, meaning the shaft extends through both sides of the motor. The pulley is on the inside, where the belt rides, and the blower wheel attaches to the opposite end outside the motor.
The blower wheel actually screws onto the shaft counterclockwise. Sounds simple enough, right?
Well, after a few unsuccessful attempts, I finally decided the best approach was to remove the motor and reposition it. That allowed my wife to push the new blower wheel through the cabinet while I threaded the motor shaft into it from the inside.
Finally! We had it installed.
I asked her to make sure the blower wheel spun freely and wasn’t rubbing against the cabinet. Everything looked good, so I proceeded to put the dryer back together.
After all that work, I was feeling pretty confident.
I soaked a towel, placed it in the dryer, thanked my wife for helping me, set the timer, and pushed the start button.
Surely, we had finally conquered this thing!
About 30 minutes later, I went back to check the towel.
Still wet.
You have got to be kidding me!
After four hours of working on this dryer, cutting parts off, heating things with a torch, repositioning motors, and replacing enough components to make a parts department happy, the dryer was STILL not drying clothes properly.
I honestly can’t describe the disappointment. There’s nothing quite like spending an entire afternoon repairing something only to discover that it still doesn’t work.
After supper, I grabbed my trusty voltmeter once again and started checking everything. I checked the connections, the safety devices, and the voltage coming into the dryer. Everything was correct.
I’m officially scratching my head!
I’ve now ordered a dryer vent cleaning brush. When it arrives, my next project will be cleaning out the exhaust vent that runs from the dryer to the outside of the house. I did confirm that there is airflow coming out of the vent, but that doesn’t necessarily mean there isn’t a partial blockage restricting it.
Most of the suggestions I’ve received point toward a clogged or restricted dryer vent, so that’s my next avenue of investigation.
At this point, I’m beginning to think the dryer has developed a personal grudge against me.
Here’s the funny part. I can troubleshoot complicated heating and air-conditioning systems, work on electrical equipment, and repair mechanical devices, but apparently, a clothes dryer is going to be my undoing.
I’m not giving up, though. I’ve invested too much time, money, and pride in this thing to surrender now!
I’ll keep everyone posted on the next chapter of “The Dryer That Almost Beat Me!”
And if nothing else, when this is all over, I’ll know a whole lot more about clothes dryers than I ever wanted to know!
Discover more from Grayfeathersblog
Subscribe to get the latest posts sent to your email.
“Apparently, YouTube forgot to mention a few things.” Too funny! YouTube is pretty great, helped my husband trouble shoot a seized part in our RV water pump, instead of replacing the whole pump. Win! But this dryer sounds like the NTSB combing through airplane wreckage to determine the cause of a crash, which kind of makes it a gripping tale. Looking forward to the next chapter. 🙂